DOCAN ENERGY HIGH CAPACITY STORAGE

MOON 48KWH LIFEPO4 BATTERY

51.2v 942ah energy storage with 48pcs 314ah lifepo4 cells, 200a continuous output, 2a active balancing, touchscreen and smart communication.

48 PCS 314AH CELLS

a 16-series 3-parallel lifepo4 cell configuration delivers high capacity at a standard 51.2v system voltage.

200A CONTINUOUS OUTPUT

supports demanding compatible loads while the battery management system monitors voltage, current and temperature.

2A ACTIVE BALANCING

high-current cell balancing helps manage cell consistency across the large-capacity battery pack.

TOUCHSCREEN MONITORING

view voltage, soc, temperature, current, cycle count and cell information directly on the battery.

INVERTER COMMUNICATION

rs485 and can interfaces support communication with compatible inverters and monitoring equipment.

UP TO 16 PACKS PARALLEL

parallel communication addresses can be configured by dip switch for supported multi-pack systems.

MOBILE CABINET DESIGN

LARGE CAPACITY IN A FLOOR STANDING ENCLOSURE

the battery measures 1000 × 420 × 830mm and weighs approximately 337kg. integrated wheels support positioning during installation and service.

install the product on a level load-bearing surface with adequate clearance, ventilation and access to the terminals, breaker and communication ports.

SMART BMS PROTECTION

CONTINUOUS MONITORING AND SYSTEM PROTECTION

• cell and pack overvoltage and undervoltage protection
• charge and discharge current detection and protection
• output short-circuit protection
• four cell temperature channels, one ambient channel and one mos channel
• real-time soc calculation and cycle statistics
• charge and discharge mosfet switching
• led capacity, run and alarm indicators
• historical operating data storage

TOUCHSCREEN

check pack voltage, soc, temperature, current, remaining capacity, cycle count and individual cell data.

BLUETOOTH APP

monitor supported battery information from a compatible android or ios mobile device.

PC MONITORING

view operating data and supported settings through the pc monitoring interface and communication connection.

SOLAR ENERGY STORAGE

store energy from a compatible solar inverter for use when solar generation is limited.

OFF-GRID SYSTEMS

support high-capacity off-grid installations with correctly sized charging and conversion equipment.

BACKUP POWER

provide stored energy for compatible essential loads during utility interruptions.

COMMERCIAL STORAGE

use in properly engineered workshops, farms and commercial energy systems where local codes allow.

CHARGING AND CONNECTION

• use a compatible lifepo4 charger or inverter with a charging voltage of 58.4v.
• verify positive and negative polarity before connection.
• series connection is not supported and may cause irreversible damage.
• do not plug or unplug connection kits while the system is operating.
• use cables, terminals, breakers and protective devices rated for the system current.
• if a parallel system load exceeds 200a, follow the manufacturer's multi-terminal output instructions.

INSTALLATION ENVIRONMENT

• install in a dry, ventilated and code-compliant battery area away from fire and combustible materials.
• do not install, charge or store in areas classified as fire-safety risk zones or crowded locations.
• do not expose the battery to water, saltwater, impact, crushing, puncture or unauthorized modification.
• do not use a battery that has been impacted, deformed or damaged.
• installation and commissioning should be completed by qualified personnel.

HOW MUCH ENERGY DOES THE MOON BATTERY STORE?

the 51.2v 942ah pack stores approximately 48.23kwh of nominal energy. actual usable energy depends on system settings, operating temperature, load and inverter efficiency.

WHAT CELLS ARE USED?

the specification lists 48 pcs 3.2v 314ah lifepo4 cells arranged in a 16s3p configuration.

CAN SEVERAL BATTERIES BE CONNECTED IN PARALLEL?

yes. the rs485 parallel communication interface supports up to 16 battery packs, with a unique dip-switch address required for each pack. series connection is not supported.

WHICH INVERTER PROTOCOLS ARE SUPPORTED?

the specification lists selected srne, voltronic and geowatt protocols through rs485, and selected victron, pylon and geowatt protocols through can. confirm the exact inverter model before ordering.

DOES THE BATTERY SUPPORT BLUETOOTH AND TOUCHSCREEN MONITORING?

yes. the battery supports local touchscreen monitoring and a compatible bluetooth application for android and ios.

WHAT IS THE MAXIMUM CONTINUOUS DISCHARGE CURRENT?

the specification lists a maximum continuous discharge current of 200a. the complete system must use correctly rated cables, terminals and protection devices.